Search results for "Reliability engineering"
showing 10 items of 224 documents
Metrological Properties of the Test Setup for Determination Shielding Effectiveness of the Industrial Cable Connectors
2017
Abstract The paper presents results related to assessment of the repeatability and reproducibility of the measurement test setup for determination the relative value of the shielding effectiveness coefficient of the industrial connectors. The construction of the proposed test setup, the measurement method and the procedure for the analysis of measurement results were described. To determine the value of the repeatability and reproducibility coefficient, the two–way analysis of variance was used, which additionally allows for an assessment of the influence of individual sources of variance. The measurements and their analysis were conducted for several frequencies in the range up to 1 GHz. A…
A methodology for evaluating the flexibility potential of domestic air-conditioning systems
2020
The paper presents a methodology for quantifying the electrical flexibility potential of air-conditioning systems (ACS) installed in residential buildings according to the building envelope characteristics and the ACS performance. In order to provide a thorough analysis of the issue, the ACS baseline consumption referred to the indoor temperature of 24°C has been computed for three typical residential buildings built in the South of Italy over different periods. The baseline consumption was used as a reference to estimate the effect of the set point temperature change on the ACS power profile. The results showed that increasing the set-point temperature of ACS by 2°C and 4°C leads to a redu…
Experimental results on the economic management of a smart microgrid
2020
The aim of this paper is to assess economic benefits deriving from the adoption of a smart microgrid. To this end, a case study consisting of 250 houses connected to the distribution network through a MV/LV transformer substation has been investigated and implemented in the experimental microgrid built at the Polytechnic University of Bari, Italy. The analysis has been performed by comparing three different energy providers: the utility grid, the utility grid with the inclusion of non-programmable renewables generators, and the inclusion of such residential loads into a smart microgrid. The obtained results demonstrated that with the adoption of a smart microgrid significant costs savings c…
A review of diagnostics and prognostics of low-speed machinery towards wind turbine farm-level health management
2016
Abstract Large wind farms are gaining prominence due to increasing dependence on renewable energy. In order to operate these wind farms reliably and efficiently, advanced maintenance strategies such as condition based maintenance are necessary. However, wind turbines pose unique challenges in terms of irregular load patterns, intermittent operation and harsh weather conditions, which have deterring effects on life of rotating machinery. This paper reviews the state-of-the-art in the area of diagnostics and prognostics pertaining to two critical failure prone components of wind turbines, namely, low-speed bearings and planetary gearboxes. The survey evaluates those methods that are applicabl…
A simulated annealing-based approach for the joint optimization of production/inventory and preventive maintenance policies
2017
Even if more reliable than the past, the performance of modern manufacturing systems is still affected by machine’s deteriorations and breakdowns. As a consequence, adequate maintenance programs must be implemented to adequately satisfy demands during manufacturing stops due to unexpected failures or preventive maintenance (PM) actions. Despite production and maintenance are closely related issues, their joint optimization has become an important research topic just during the last decade. Therefore, the present paper proposes a model for the combined optimization of production/inventory control and PM policies with the aim of minimizing the total expected cost per unit time. The model is f…
The ELECTRE I method to support the FMECA
2018
Abstract In traditional Failure Modes, Effects and Criticality Analysis (FMECA), risk priorities of failure modes are determined through the Risk Priority Number (RPN), which is a function of the three risk parameters Occurrence (O), Severity (S), and Detection (D). In the present paper, an alternative approach to RPN is proposed for the criticality assessment of system failure modes. Particularly, the Multi-Criteria Decision Making (MCDM) method ELECTRE I is proposed to select the most critical failure mode in the set of the failure modes charactering a complex system. The method has been applied to a case study previously proposed by Zammori and Gabrielli (2012).
Predictive shelf life model based on RF technology for improving the management of food supply chain: A case study
2016
The aim of this paper was the development of a Smart Logistic Unit (SLU) based on RF technology to support the management of the food supply chain, in order to guarantee the shelf life of products in agreement with logistic efficiency and system sustainability. For this purpose, the main parameters that influence the quality of perishable products were determined and a shelf life equation based on Volatile Organic Compounds (VOCs) was modelled. The levels of VOCs were gathered by the sensors allocated inside the SLU, which configures as the remote element of a system for identification and data transmission. The proposed model was then validated through an experimental test, simulating the …
Automatic crack detection results using a novel device for survey and analysis of road pavement condition
2019
To accurately schedule maintenance operations, it is crucial to monitor the pavement state and, thus, evaluate the structural and functional indices during its entire service life. In particular, surface conditions (cracks, potholes, patches, rutting, etc.) must be properly checked – especially in terms of detection, identification, and classification of distresses – for avoiding reaching dangerous values for users (overpassing safety thresholds). However, monitoring and survey activities can be so costly (not only in economic terms, but further considering the execution time) to discourage their execution, with evident drawbacks for a proper maintenance management and the related intervent…
Design Issues and Sample Size when Exposure Measurement is Inaccurate
2001
AbstractMeasurement error often leads to biased estimates and incorrect tests in epidemiological studies. These problems can be corrected by design modifications which allow for refined statistical models, or in some situations by adjusted sample sizes to compensate a power reduction. The design options are mainly an additional replication or internal validation study. Sample size calculations for these designs are more complex, since usually there is no unique design solution to obtain a prespecified power. Thus, additionally to a power requirement, an optimal design should also fulfill the criteria of minimizing overall costs. In this review corresponding strategies and formulae are descr…